Inconel 718 Beam Manufacturer

Sachiya Steel International is one of the Leading Manufacturer And Exporter Of High Quality Inconel 718 Beam, which has high strength properties, worthy workability and good weldability. Age – hardening treatments are not required, as Inconel 718 Angle is hardened and strengthened through cold work only. Inconel 718 C-Channel is highly resistant to chloride – ion stress – corrosion cracking due to the high nickel content, where low sulfur plummeting furnace environments should be utilized in forging. Inconel 718 H-Beam is resistant to a wide range of corrosive media and has developed into a wide spectrum of applications for high temperature strength and corrosion resistance.

Inconel 718 Beam Manufacturer In India | Inconel 718 Beam Manufacturer In Mumbai | Inconel 718 Beam Exporter In India | Inconel 718 Beam Exporter In Mumbai | Inconel 718 Beam Supplier In India | Inconel 718 Beam Supplier In Mumbai | Inconel 718 Beam Stockist In India | Inconel 718 Beam Stockist In Mumbai 
Inconel 718 Beam
                  Inconel 718 Beam

For heavy hot work in Inconel 718 I-Beam, the range should be in between 1900 Degree F and 2250 Degree F (1040 Degree C and 1230 Degree C); light work can be done to 1718 Degree F (870 Degree C). Inconel 718 T-Beam is a superior choice for gas turbine components including jet engines, titanium dioxide plants and chlorination equipment to 1000 Degree F.

The chromium content of Inconel 718 Chain gives better resistance than Nickel 200 and Nickel 201 under oxidizing conditions, at the same time the high nickel gives good resistance to reducing conditions. Fine grain Alloy 718 Angle typically has better corrosion resistance as well as fatigue, impact and higher tensile properties. The strength and oxidation resistance of these Alloy 718 C-Channel at high temperatures make it useful for many applications in the heat – treating industry.

Inconel 718 Angle, Channel, Beam, Chain Specifications

Specifications : ASTM B166 / ASME B166
Dimensions : EN, DIN, JIS, ASTM, BS, ASME, AISI
Inconel 718 Angle
: 5mm to 9mm
Inconel 718 Channel
: 40mm*20mm~300mm*300mm
Inconel 718 Beam : 3″ thru 12.31″
Inconel 718 Chain
: 1/8 inch – 1/2 inch Diameter
: 3.0mm – 120mm
Length : 3MTR, 4MTR, 5MTR, 6MTR, or Custom Cut Sizes
Type : Angle, C Channel, U Channel, H Beam, I Beam, T Beam, W Beam, Chain

718 Inconel Angle, Channel, Beam, Chain Chemical Composition

Grade C Mn Si Cr S Fe Mo Ni Cu
Inconel 718 0.08 max 0.35 max 0.35 max 17.0–21.0 0.15 max  – 50.0-55.0 min 0.30 max

Inconel 718 Angle, Channel, Beam, Chain Mechanical Properties

Density Melting Point Tensile Strength Yield Strength (0.2%Offset) Elongation
8.2 g/cm3 1.350 °C (2460 °F) Psi – 1,35,000 , MPa – 930 Psi – 75,000 , MPa – 482 45 %

Equivalent Grades for 718 Inconel Angle, Channel, Beam, Chain

Inconel 718 2.4668 N07718 NCF 718

Inconel 718 Angle, Channel, Beam, Chain Application Industries

  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry

718 Steel Angle, Channel, Beam, Chain Test Certificates

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc

Material Testing

We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and Macro Test
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test


• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

Leave a Comment

Your email address will not be published. Required fields are marked *